Electrolux dishwasher error code displayed — i60

Use only checks that match the exact appliance or system and its official guide.

1. Check 1

   Before resetting anything, photograph or transcribe the complete display and write down every character, capitalization, flashing-light or beep pattern, the programme stage, and whether the dishwasher stopped, failed to heat, or failed to dry. Photograph the rating label or record the full model/product number and the country or market; do not pull out an integrated appliance just to find it.

   Expected result: The display is clearly i60 on a dishwasher and the model/market is recorded, or the display is partial/different, only lights flash, or the model and market remain unknown.

   Next step: Use the exact regional owner manual when the identity is known. If the identity or display is incomplete, keep the record and contact Electrolux support instead of applying a universal code chart.

   Stop if: Do not enter service mode, alter configuration values, or open panels to locate the rating label. Stop if there is leaking, smoke, burning odor, damaged wiring, abnormal heat, or a repeated electrical protection trip.

   Why this matters

   Why: A clear i60 supports Electrolux's heating-related branch, while a different code or panel pattern needs its own matching support article. Missing identity prevents safe use of a model-specific reset or internal procedure.

2. Check 2

   Without opening the dishwasher or disconnecting plumbing, check the accessible household water-supply setting or a safe measurement at the connection point. Electrolux's i60 guidance says the inlet water temperature should not exceed 60°C; keep the exact model instructions and local plumbing requirements in control.

   Expected result: The inlet supply is above 60°C, its temperature cannot be established safely, or it is at or below 60°C.

   Next step: If the supply is too hot, have the household or plumbing setup corrected through a safe documented adjustment. If it is within the limit or remains unknown and i60 persists, continue only with the power-isolated accessible check rather than selecting a heater part.

   Stop if: Do not loosen a water connection, disconnect a hose, change plumbing while the appliance is energized, or use a code to justify a hot-water installation alteration.

   Why this matters

   Why: An over-temperature inlet can adversely affect detergent performance and washing results and is an installation condition to correct safely; it does not prove that the internal heater or sensor has failed. An unknown temperature is not evidence that the supply is suitable.

3. Check 3

   If there is no leak or electrical hazard, turn the dishwasher off and unplug it or isolate the circuit only from a dry, safe position. Following the matching manual, inspect the removable filters and sump for foam, suds, or debris and clean only those accessible parts. Do not remove the sump, heater, pump, sensor, or control cover.

   Expected result: Foam or debris is present in the filters or sump, those areas are clear, or there is standing water in an unsafe location, a leak, or visible damage.

   Next step: Clear only accessible foam or debris and refit the filters as the exact manual shows. For a leak, uncontrolled standing water, or damage, keep the dishwasher off, close the water tap if safe, and arrange service.

   Stop if: Do not reach into a hidden sump or pump, remove internal panels, handle suspected sharp debris, or operate the dishwasher with a wet electrical area.

   Why this matters

   Why: Electrolux's i60 instructions specifically call for checking filters and the sump for foam/suds and debris after safe power isolation. Clearing an accessible obstruction may remove a temporary condition, but a clear sump does not identify an internal heating component. Water or damage near electrics overrides routine cleaning.

4. Check 4

   Only after the display and model record are saved, the appliance is dry, filters are refitted, and the exact regional article permits it, reconnect power once and select a suitable normal cycle. Do not use a hidden diagnostic sequence or keep cycling the breaker; if your model's manual specifies a different reset or cancellation control, use that manual instead.

   Expected result: The display clears and one normal cycle operates, i60 returns immediately or during the cycle, a different code appears, or the dishwasher still does not heat or dry.

   Next step: Keep the before-and-after record. If i60 returns or heating/drying remains abnormal, stop using the dishwasher and arrange an approved Electrolux service visit with the model, market, code, and cycle-stage notes.

   Stop if: Do not restart after a leak, smoke, burning odor, abnormal hot surface, breaker/RCD trip, or visible wiring damage. Do not select a heater, sensor, pump, or board from i60 alone.

   Why this matters

   Why: Electrolux allows a limited reset/check path on the opened i60 pages, but a successful start does not prove that every heating condition is healthy. Recurrence, a changed code, or persistent no-heat/no-dry behavior requires model-specific service rather than repeated resets.

5. Check 5

   If the exact model manual includes a Machine Care or descaling programme, check that manual before using it; use only a dishwasher-approved descaler and the stated dose. Do not substitute a generic chemical, combine cleaners, or run a high-temperature care cycle to force i60 to clear. If the manual does not confirm this option, skip it.

   Expected result: The matching manual confirms Machine Care/descaling, does not include it, or i60 is accompanied by abnormal heat, odor, leakage, or another code.

   Next step: Use the care programme only if the exact manual and product label match. Otherwise preserve the code record and arrange service for recurring i60 or continuing heating/drying failure.

   Stop if: Never mix descaler with other cleaners, open the machine during a hot care cycle, bypass a safety response, or use descaling as a substitute for electrical diagnosis.

   Why this matters

   Why: The Australian Electrolux i60 page includes filter/sump and spray-arm checks and a dishwasher-descaler Machine Care path, but that regional instruction cannot establish that an unidentified model has the same programme. Safety symptoms or a second code need service, not chemical cleaning.