Fisher Paykel Dishwasher Repair Guides

First identify whether your Fisher & Paykel dishwasher is a conventional full-size model or a DishDrawer, because the filter and drain path are different. A new-appliance smell may fade after a few wash programmes, but an established odor is more consistent with dirty filters, food left on dishes, a dirty interior, or water that is not draining.

First identify whether the appliance is a DishDrawer or a traditional drop-door Fisher & Paykel dishwasher, and whether it is paused, showing a fault, left with water, or stopping without a code. Check the closed drawer or door, keylock and delayed start, then the water supply and visible drain path. Use the exact model guide for any A/F code; do not keep resetting a persistent fault or work inside the powered appliance.

Do not diagnose a Fisher & Paykel dishwasher from a generic code list. First record the complete model code, whether the appliance is a DishDrawer or a drop-door dishwasher, the exact letters/numbers or flashing indicators, any beeps, and which drawer or door is affected.

For a leaking Fisher & Paykel dishwasher, first identify whether it is a DishDrawer with one or two sliding drawers or a conventional drop-door dishwasher, and note whether water is leaking from the inlet, drain, drawer or door perimeter, or from underneath. Stop the cycle, keep hands out of hot water, wipe up accessible water, and turn off the water and power if the leak is active, heavy, near electrical parts, or accompanied by a flood indication.

First identify whether your Fisher & Paykel dishwasher is a single or double DishDrawer, an integrated or built-under installation, and when the sound occurs. A fan running after a wash, a quiet phase during a program, a pulsing sound while rinse aid dispenses, and some water-softener or drain sounds can be normal on the DishDrawer models covered by Fisher & Paykel guides.

First decide whether this is a normal small amount of water in a DishDrawer filter area or true standing water across a drawer or traditional tub. On a DishDrawer, switch off and allow it to cool before cleaning the user-accessible drain filter and filter plate, then check the drawer's drain hose and waste connection for a kink or blockage.

First identify the Fisher & Paykel architecture: a conventional DW60 door dishwasher uses a door latch and a Start/Pause control, while a DishDrawer runs each drawer independently and adds drawer-specific Keylock or Childlock, delayed-start timing, and (on some models) Demo mode. With the appliance dry and cool, check external power, close the correct door or drawer normally, clear only the lock or delay state described by the exact model guide, and record any fault display.

First decide what is still running. On Fisher & Paykel DishDrawer models, fan noise after a completed program can be normal: the fan assists drying and should stop after a set time or when the drawer is opened.

First separate a completely dark dishwasher from one whose panel or drawer indicators are lit. Fisher & Paykel sells two distinct dishwasher platforms: DishDrawer models with one or two independently operated drawers, and traditional drop-door models.

First define what “not working” means on the exact Fisher & Paykel dishwasher: no lights or response, controls that respond but will not begin, a cycle that starts but does not fill, or a cycle that leaves water behind. Fisher & Paykel's dishwasher troubleshooting guides point first to power, a fully closed door, the model's Start/Pause control, an open water tap, and a blocked inlet strainer; some models also list Keylock as a reason buttons beep without starting.

For a Fisher & Paykel DD603 DishDrawer, the opened legacy NZ/AU user guide lists F2 as a motor problem and directs the owner to an Authorised Service Centre. That mapping is tied to the DS603/DD603 guide published for this older generation; do not borrow an F2 explanation or reset sequence from a newer DishDrawer or another dishwasher.

For a Fisher & Paykel DD60SCTX7 DishDrawer that leaves dishes dirty, start with the parts of the wash that can be observed without service access: load the drawer so the spray arm can rotate, confirm the filter plate and drain filter are seated and clean, and check that the detergent is suitable, correctly placed, and measured for the selected program. Then separate hard-water or rinse-aid symptoms from a remaining circulation, heating, water-inlet, or drawer-seal fault.

Do not treat A3 as a universal Fisher & Paykel code. The opened Fisher & Paykel guides show that A3 is used on particular DishDrawer platforms for a drain condition, but the exact model, drawer or door platform, display pattern, and market must be matched before any code instruction is used.

Do not assume every Fisher & Paykel dishwasher uses F1 the same way because the model is not identified. In the Fisher & Paykel DishDrawer care guide opened for this research, F1 is a flood fault and the guide says to drain the dishwasher; the same guide treats excess foam as a separate A7 condition and says to stop, wipe away foam, and run a rinse cycle with the correct detergent.